Which combination to use
Werp™ recommends these six combinations. The print screen is the one that opens when you make labels (how to open it is on the QR labels page). The same combinations are listed under “How to print” in Settings → “QR labels”, marked with whether each was tested.
Choosing your printer in the setup under Settings → “QR labels” makes the matching label type, tape width and output the workspace default, and the print screen always starts from it.
| Printer | Device and software | What to choose on Werp™'s print screen | Tested on a real printer |
|---|---|---|---|
| TEPRA PRO (SR-MK1 and others) | iPhone or Android with the TEPRA app | “Label tape” → width → “PNG” → “Download PNG” | Verified to work |
| TEPRA PRO (SR-MK2, SR-R5600P, SR5900P and others) | Windows with TEPRA Creator | “CSV” → “Shift_JIS” (Japanese Windows) | Not verified |
| Brother P-touch CUBE PT-P910BT | Computer with the printer driver | “Label tape” → width → “PDF” → “Save PDF” | Not verified |
| Brother P-touch CUBE PT-P910BT | iPhone, iPad or Android with Brother Smooth Print | “Label tape” → width → “PDF” → “Print with Smooth Print” | Not verified |
| Brother P-touch CUBE PT-P910BT | Computer with P-touch Editor | “CSV” | Not verified |
| White film label sheets | Computer with a laser printer | “Label sheets” → sheet → “Save PDF” | Verified to work |
TEPRA PRO (King Jim)
King Jim's official information doesn't mention a printer driver for computers or AirPrint for the TEPRA PRO (as far as Werp™ checked on November 21, 2026). So we don't recommend the PDF output for TEPRA; use a PNG image from a phone, or a CSV on Windows.
From an iPhone or Android (SR-MK1 and others)
- On the print screen, set “Label type” to “Label tape”, “Tape width” to the width of the tape in the TEPRA (18 mm is the standard), and “Output” to “PNG”.
- Tap “Download PNG”. On an iPhone the share sheet opens; choose “Save Image” to save it to Photos.
- In the TEPRA app, load the saved image and print it. For the steps inside the app, see King Jim's instructions.
Several labels made at once come out as one long image with dots marking where to cut. Print that image on one strip of tape from the TEPRA app, then cut along the dots.
This is the combination the Werp™ team uses day to day, on an SR-MK1 with an iPhone, and it prints. The SR-MK1 is used from a phone over Bluetooth and doesn't work with computer software or drivers; models such as the SR-MK2 can be used from a computer (King Jim's product pages).
From Windows (TEPRA Creator)
- Click “CSV” at the bottom of the print screen and, in the “For merging into TEPRA Creator or P-touch Editor” menu, choose “Shift_JIS” to save (for Japanese Windows; with other software, choose “UTF-8”).
- In TEPRA Creator, make the label layout with a QR code and text fields for the name, code and so on.
- Load the CSV as the data to merge. For the QR field, set the column's attribute to “Barcode” with the QR code type, then link it to the qr column. Link the text fields to columns such as name and code (see the merge and barcode sections of the TEPRA Creator manual).
- Save the layout as a template. From then on, load a new CSV and print.
From a Mac
On a Mac you have TEPRA LINK 2 (macOS 13 or later; for models such as the SR-MK2 and SR-R5600P, not the SR-MK1, per King Jim's official pages). King Jim's instructions don't mention loading a CSV or an image. Even when you work on a Mac, print TEPRA labels with the phone steps.
P-touch CUBE PT-P910BT (Brother)
The PT-P910BT prints PDFs from a computer through the printer driver, and from a phone with Brother Smooth Print (Smooth Print support is listed in Brother's information; the PT-P710BT isn't in that list). Werp™'s “PDF” output is a PDF the width of the tape, with one label per page. The 18 mm PDF has the same layout as the PNG.
- Use 18 mm TZe laminated tape as the standard. For a QR code that is easier to scan, use 24 mm. 12 mm prints, but the QR code becomes small and harder to scan.
- For surfaces where labels peel off, the strong-adhesive TZe-S suits better. Brother publishes test results showing TZe tape resists water and abrasion, but that is not a guarantee.
From a computer (printer driver)
- On the print screen, choose “Label tape”, set “Tape width” to the tape in the printer, set “Output” to “PDF” and click “Save PDF”.
- Open the saved PDF, print it and choose the PT-P910BT as the printer.
- Set the scale to 100% (actual size). “Fit to page” changes the size of the QR code and the text.
From an iPhone, iPad or Android (Smooth Print)
- On the print screen, choose “Label tape”, set “Tape width” to the tape in the printer, set “Output” to “PDF”, and tap “Print with Smooth Print” (to the left of “Save PDF”). While it prepares, it shows “Preparing…”.
- When the button changes to “Open Smooth Print”, tap it again. Smooth Print should open with that tape width; print from Smooth Print. It can't open if Smooth Print isn't installed. The prepared link stops working after 9 minutes.
If the PDF can't be handed over, save it with “Save PDF” and share it to Smooth Print (on an iPhone the share sheet opens when you save; on Android, open the saved PDF and share it). For the steps inside Smooth Print, see Brother's instructions.
“Print with Smooth Print” uploads the PDF to Werp™'s server for a short time and gives Smooth Print a URL that can be read only for a limited time. The uploaded PDF is deleted automatically after about a day and isn't kept with the equipment records. How several labels in one PDF are printed has not been tested by Werp™.
Printing many at once in P-touch Editor on a computer
- Click “CSV” at the bottom of the print screen and choose the encoding in the menu that opens to save it. For P-touch Editor on Japanese Windows, choose “Shift_JIS”.
- In P-touch Editor, make the label layout and load the CSV as a database.
- Place a QR code barcode and drag the qr field onto it, and drag fields such as name and code onto the text. Save the layout to reuse it next time.
Label sheets and a laser printer
Without a tape printer, we recommend white film label sheets made for laser printers, printed on a laser printer.
- If the sheet's layout (margins, number of labels, gaps) isn't in the workspace's list of sheets, make one with the same measurements under Settings → QR labels → “Label sheets”. Take the measurements from the layout drawing the sheet's maker publishes.
- On the print screen, set “Label type” to “Label sheets”, pick that sheet under “Sheet” and click “Save PDF”.
- Print the PDF on a laser printer at 100% (actual size).
The CSV for label software
“CSV” at the bottom of the print screen (it opens a menu headed “For merging into TEPRA Creator or P-touch Editor”) writes the selected units, one per row. The column names are fixed, and every column is included regardless of which lines the workspace prints, so one template keeps working.
| Column | Contents |
|---|---|
qr | The URL for the QR code. Scanning it opens that unit's page |
name | Unit name (the nickname, or the item name if there is none) |
code | Unit code |
asset_number | Asset number |
model | Maker and model |
serial_number | Serial number |
purchase_date | Purchase date |
owner | Owner (the workspace name, or the owner's name for a personal item) |
- Choose the encoding: “Shift_JIS” (TEPRA Creator and P-touch Editor on Japanese Windows) or “UTF-8” (other software). Characters that Shift_JIS doesn't have become “?”, and the screen shows how many.
- Values that start with = + or @ get a ' in front, so a spreadsheet doesn't run them as formulas.
- Werp™ doesn't provide template files for TEPRA Creator (.lw1) or P-touch Editor (.lbx), because their formats aren't published. Make one once with the steps above.